How to Set a Mono Pump Skimmer for Optimal Performance

by | Apr 27, 2017 | Equipment | 8 comments

skimmer, sump

Last week, we discussed skimmer maintenance (article). Today, we’ll discuss how to set the skimmer for optimal performance. We’ll be focusing on mono pump skimmers, but the suggestions apply to all types.

The first thing you need to know is that the skimmer is deeply influenced by the salinity of the water. The saltier the water, the more foam produced.; in fact, the skimming theory doesn’t work for freshwater. We suggest that you keep the salinity valor to 35 parts per thousand, or 1023.3 g/dm3 with 25°C of density. You can read  this article to explore this topic further.

Preliminary operations

We highly recommend reading the skimmer manufacturer’s instructions, and follow their advice on where to set the height of the water in sump, it will make a big difference in how well the skimmer works.

skimmer, sump

If you don’t have that information, a value about 21 cm (8 in) is a good start. In my new sump, pictured above, I chose to keep the water at 20 cm so the skimmer will work in a fixed level of 21 cm.

A fixed water level in the sump allows you to obtain perfect regulation of your skimmer. Usually, a double pump skimmer (with an input pump) suffers less from a variation of the level in the sump.

Even an oscillation of 1 cm can make the skimmer over foam or under foam, depending on the level of the variation.

sump

In order to avoid considerable oscillations, we recommend installing an automatic top off system.

How to regulate a mono pump skimmer (and the others)

Usually the skimmer is regulated by a couple of parameters: water and air inlet. Every manufacturer has a different ideal value for these, as well as the ideal relationship between the two.

skimmer, sump

Except for skimmers with unconventional shapes (like the tunze 9415 in the previous picture), you want the water level to reach just under the neck of the glass. Generally, I prefer to keep the air all the way open and concentrate on the drain level.

  1. Open the air totally. Sometimes there’s a little tap, other times a gate valve, and on others still, you open the air by rotating the entrance of the pump (like in Vertex’s).
  2. Regulate the water to raise its level to just over the base of the glass (with the bubbles rising a few centimeters over that).

Sometimes, even if you’ve followed these two directions perfectly, the glass gets full too quickly because the level is too high. In this case, you have to decrease the amount of air.

Now the skimmer is completely regulated.

skimmer

If you want more…

So regulating the skimmer in this way, we obtain almost the best performance, but we can improve it even further by addressing the oscillations in the amount of the air entering the unit.

flow measurement

You can avoid this with a flow measurement like the one pictured above, then regulate the air and obtain a fixed level. Normally, this can be accomplished by closing the air a little bit.

Dry and wet skimming

The balancing of air and water in the entrance lets us change the density of the liquid in the glass. When the level in the skimmer is higher and the content of the glass is very liquid, that’s “wet skimming”. Otherwise, it’s called dry skimming, with a lower level and a denser content.

skimmer

I prefer wet skimming. In this way there are more surfactants extracted by the water and the quality of the water is superior.

skimmer

Dry skimming is important in a aquarium lacking in nourishment, as there are less surfactants removed.

In summary: if the skimmer is overdimensioned choose dry skimming, and if it’s underdimensioned, use wet skimming.

Skimmers with regulable pumps

We’ve seen a few skimmers on the market that are equipped with regulable pumps. These pumps work with low voltages and so maybe they’re safer, but I don’t think they provide any great advantages. The skimmer has to be chosen depending on the aquarium in which it will be placed.
Changing the range of the pump would unbalance the air and water in the skimmer, but water and air ranges are rather fixed once given the geometry of the skimmer. So I prefer not to use this type, and therefore avoid having to regulate the range of the pump.

skimmer

If you have any questions feel free to ask in the comments. And remember to clean the glass often: it’s one of the most important things you can do to keep your skimmer working at top efficiency!

[translated by Agnese Poggi]

  • danireef

    Danilo Ronchi, aka DaniReef lives in Italy where he is hydraulic engineer, but starting from his love for reef aquarium and photography, he began to write about marine aquariums from 2006 and now he's published his first book "Marine Aquarium". From 2007 Danilo writes on his blog danireef.com where publishes articles, pictures, product reviews, aquariums coverage, reportage and history of his tank. Now he's happy to be part of Reefs.com

8 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *

Upcoming Events