Help me design a monti scraper

[duke62]

I have encrusting montis that are on a separate rock on the floor on my cutting board. Well they are growing fast and if anyone has seen me I am vertically challenged lmao. I need to cut then scrape these montis off my cutting board and with my short arms and bad back I can not get into the tank with a razor to cut them. I need to make a razor pole that will cut the monti easily and then be able to get under it to get it off the cutting board. Show me you best design for this cutting pole. It will need to be able to be able to change the blade with salt water it will rust pretty quick. Best design will get a free monti pack. I don't want a discussion on how to do it I want you guys to
Do it for me

 

[bonomo53]

hey duke what about something like this http://www.drsfostersmith.com/produ...=pla&catargetid=530005150000135617&cadevice=c

 

[ducati335i]

That's tough! Not too sure... Can't leave them?

 

[bigsink]

I will be more than happy to do it.

 

[Dk638]

I can make one out of stainless steel.

 

[lnevo]

You couldnt do it with a kent scraper?

 

[Arati]

we do that for you

 

[duke62]

Can't use a scraper. I want something that can attach a real razor to to cut where I want it then use another sharp razor to get underneath to scrape the area I just scored.

 

[MysticalKnight]

Get a length of small diameter pic pipe, put a very small angled slit in it and then drill a hole at the base of the slit on each side, then just slide a razor into it. Cost about 3 dollars maybe. I have one I made at home if you are confused I can post a pic of it later when I get outta work

 

[MysticalKnight]

PVC not pic, auto correct fail

 

[jgraz]

I just made a scraper out of the pole used to open and close mini blinds. Wife wasn't happy though. All I did was cut a small slit in one end and with a bit of heat bent it to my liking. Just a tiny touch of super glue held the razor in then slit. I was able to reach the bottom of a 24" tank without getting my hands wet and it scraped down months worth of corraline buildup.
After I was done the razor popped right out with the small drop of now dried glue, leaving a nice clean place for the next razor. All it cost me was some dirty looks from the wife.

 

[edd]

I just made a scraper out of the pole used to open and close mini blinds. Wife wasn't happy though. All I did was cut a small slit in one end and with a bit of heat bent it to my liking. Just a tiny touch of super glue held the razor in then slit. I was able to reach the bottom of a 24" tank without getting my hands wet and it scraped down months worth of corraline buildup.
After I was done the razor popped right out with the small drop of now dried glue, leaving a nice clean place for the next razor. All it cost me was some dirty looks from the wife.

home depot sells those rods, so you can keep your wife happy.

 

[MysticalKnight]

I just made a scraper out of the pole used to open and close mini blinds. Wife wasn't happy though. All I did was cut a small slit in one end and with a bit of heat bent it to my liking. Just a tiny touch of super glue held the razor in then slit. I was able to reach the bottom of a 24" tank without getting my hands wet and it scraped down months worth of corraline buildup.
After I was done the razor popped right out with the small drop of now dried glue, leaving a nice clean place for the next razor. All it cost me was some dirty looks from the wife.

I tried that first and ended up going with 1/2" pvc because I found the rod too flimsy

 

[MikeC]

 

[MikeC]

Loos like Duke62 owes u a frag pack

Lol no way man DUKE has given me so much over the last few years I owe him.

 

[MikeC]

I also made this one if it can help any one ells out.