• Why not take a moment to introduce yourself to our members?

tld

Active Reefer
Rating - 0%
0   0   0
Just as extra practice on the router I started making copies of the templates from MDF board. I found this stuff more unnerving to cut than the acrylic. Two observations - the MDF had a tendancy to catch and jump out. Also instead of chips, it made a fine powder - enough to make me put a mask on 8O

To lesson the amount of powder I was producing, I used the table saw to trim away as much excess board as possible. This seemed to help a little.

I didn't want to use my new acrlyic bit on the MDF board so I bought a different one - this one was a triple flute 1/2" lamininate flush trim bit. It was not an upcut bit - Lowe's didn't have any and I was too impatient to order one. Is this bit causing my difficulties or is a common problem with MDF? I would have guessed that it would be easier to route than acrylic, but I really didn't like it jumping out on me.

Also, it dawned on me that I'm not going to be able to use this 1/2" bit to finish copying the templates. :roll: Would it be okay to use my new acrylic bit to finish up a few holes? I don't want to ruin it.

One final question - that 90 degree angle in the L of the ovoid template is pretty sharp - what size bit do I need to make that? It looks smaller than what a 1/4" bit could cut. (Or do I need to even worry about it - it's not the side used for rounding off corners.)

Thanks,
Teresa
 

fergy

Advanced Reefer
Rating - 0%
0   0   0
MDF makes dust, there is no way around that.

Try not to use your acrylic bit, because the glue in the MDF will dull it in no time. For MDF, you don't need a spiral bit, but a two-flute cutter would have been fine for this use.

For that internal L shape, don't worry about the outside of the curve. Just make sure that the inside corner looks right.

BRIAN
_________________
Mercedes Benz 190
 

tld

Active Reefer
Rating - 0%
0   0   0
Thanks Brian,

I'll save my acrylic bits for acrylic only. When I bought the bit for the MDF board I got the triple flute instead of two-flute figuring it would cut faster and it was only a few cents more. Well, it probably does cut faster, but also produces more dust - I'll know better next time.

Is there any way to keep the MDF board from catching and jumping? Go slower?

Teresa
 

cybershark

Active Reefer
Rating - 0%
0   0   0
I made a set of templates out of 1/2" acrylic that I had laying around . I did not use the router . I felt that it would be a good project to try out a cnc mill at my sisters shop. First time ever writing programs . Pretty easy
I used 1/4"and a 3/8" double flute bits. Speed was set at 1400 rpm and the feed rate was around 20" ipm . The cut was very smooth but took for ever. With bit changeing and all on the ovoid peice it took me about 45 min just on that one peice.
 

tld

Active Reefer
Rating - 0%
0   0   0
Both Lowe's and Home Depot have it in my area. A 4'x8' sheet cost ~$17 or they have smaller pieces (something like 2'x3') near the shelving materials for less than $10.

I have not yet finished copying the template for my ovoid piece because I don't have a router bit small enough for the keyholes (other than my acrylic bit). Can anyone point me to an online source for an inexpensive bit?

Teresa
 

cybershark

Active Reefer
Rating - 0%
0   0   0
Buy yourself a new bit for acrylic and use the old on on the mdf. That whiteside bit is the cheapest 1/4" flushtrim bit.
Make sure you wear a breathing mask when routing out that mdf the resin/ glue in it will make you sick. Hope this helps
 

Sponsor Reefs

We're a FREE website, and we exist because of hobbyists like YOU who help us run this community.

Click here to sponsor $10:


Top