- Location
- Baiting Hollow Long Island NY
Boat
So I go to my boat today because for some reason, there is always water in the bilge and it drives me nuts. For 10 years I have been cramming myself in the bilge with a rag and a bottle of Lestoil so I can get the grease off of everything especially those white bilge pump hoses in between the engines. You can barely make out the red bilge pump all the way in the back. There is always grease in there because even a drop of oil in a bilge will coat everything if there is water in there.
Years ago I installed that bilge pump on a 24" piece of 1/4" plexiglass and secured the plexiglass in a place in the bilge where I can easily remove a screw and take out the bilge pump that is in a place that you can't get to.
Today I brought my camera there which has a 6' flexible hose in it so I can get the camera all the way under the engines to look for the leak.
So I removed all the water in the bilge and cleaned it nice and white. I also cleaned those corrugated hoses. I then did something else for 10 minutes and when I came back, there was water in the bilge.
I again sucked out the water with a vacuum and dried it nice and clean. I went and did something else and when I came back, there was water in the bilge.
OMG, I am going crazy, there should not be water going in there but it is a very tight spot and I can't see where the water is coming from.
It didn't help that it is 90 degrees and the sweat coming off of me is also filling the bilge.
I stick my feet up in the air and get my head all the way down there wondering how I am going to get out and I see it.
A little waterspout of water is coming into the boat from a tiny hole in the middle of the bilge, under where I have that plexiglass bracket that I made to hold the pump.
Then I figured it out. When they built the boat, the Jiboni that installed the bilge pump must have drilled the hole for the screw all the way through the hull into the sea. That must have been tough because the hull is probably 2" thick there.
He probably put in a screw he got in Home Depot because it was not stainless steel and it rotted out leaving this nice little hole where water comes in.
I got a real stainless steel screw and screwed it into the hole.
Problem solved and it only took me 10 years to find it.
I would never have found it if I didn't take the pump. bracket and hoses out to clean.
The water was probably filling the bilge about 2" deep and the bilge pump would come on pumping out most of the water until it filled again.
So I go to my boat today because for some reason, there is always water in the bilge and it drives me nuts. For 10 years I have been cramming myself in the bilge with a rag and a bottle of Lestoil so I can get the grease off of everything especially those white bilge pump hoses in between the engines. You can barely make out the red bilge pump all the way in the back. There is always grease in there because even a drop of oil in a bilge will coat everything if there is water in there.
Years ago I installed that bilge pump on a 24" piece of 1/4" plexiglass and secured the plexiglass in a place in the bilge where I can easily remove a screw and take out the bilge pump that is in a place that you can't get to.
Today I brought my camera there which has a 6' flexible hose in it so I can get the camera all the way under the engines to look for the leak.
So I removed all the water in the bilge and cleaned it nice and white. I also cleaned those corrugated hoses. I then did something else for 10 minutes and when I came back, there was water in the bilge.
I again sucked out the water with a vacuum and dried it nice and clean. I went and did something else and when I came back, there was water in the bilge.
OMG, I am going crazy, there should not be water going in there but it is a very tight spot and I can't see where the water is coming from.
It didn't help that it is 90 degrees and the sweat coming off of me is also filling the bilge.
I stick my feet up in the air and get my head all the way down there wondering how I am going to get out and I see it.
A little waterspout of water is coming into the boat from a tiny hole in the middle of the bilge, under where I have that plexiglass bracket that I made to hold the pump.
Then I figured it out. When they built the boat, the Jiboni that installed the bilge pump must have drilled the hole for the screw all the way through the hull into the sea. That must have been tough because the hull is probably 2" thick there.
He probably put in a screw he got in Home Depot because it was not stainless steel and it rotted out leaving this nice little hole where water comes in.
I got a real stainless steel screw and screwed it into the hole.
Problem solved and it only took me 10 years to find it.
I would never have found it if I didn't take the pump. bracket and hoses out to clean.
The water was probably filling the bilge about 2" deep and the bilge pump would come on pumping out most of the water until it filled again.